Miele PT 7188 Operating And Installation Instructions Download Page 10

Correct use

,

Caution! Risk of fire.

To avoid the possible danger of fire please red these warnings carefully.

,

A clogged filter is a hazard! The lint filter must be cleaned after

every programme.

~

Remove all objects from pockets such as lighters and matches.

~

To prevent the risk of fire, the following textiles must not be dried

in this tumble dryer:

– items which have not been washed.

– items, such as workwear, which have not been thoroughly

cleaned and which are still soiled with grease, oil or other
deposits (such as cosmetics, lotions etc).
If items have not been thoroughly cleaned, there is a danger that
these might ignite when heated, even after they have been
removed from the dryer at the end of the programme.

– items that have been soiled with substances such as cooking oil,

acetone, petrol, kerosene, spot removers, turpentine, waxes, wax
removers and other chemicals (e.g. mops and floor cloths) should
be washed in hot water with extra detergent before being dried in
the tumble dryer.

– items which have been splashed with hair lacquer, hair spray, nail

varnish remover or similar substances.

Warning and Safety instructions

10

Summary of Contents for PT 7188





























































Reviews: