Miele PDR 908 EL Operating And Installation Instructions Download Page 55

Page: 55 / 96

Problem solving guide

Message

Possible cause and remedy



Fault F. If restart
fails, call Miele.

lights up after a
programme has
been cancelled.

There is no obvious cause.



Follow the prompt in the display.



Touch the

sensor.

If the programme terminates again with the same
error message, then there is a fault. Contact Miele
Professional Service.



Obstruction
detected. Untangle
laundry and restart.

lights up after a
programme has
been cancelled.

The laundry is unevenly distributed or has rolled up.



Open the door and loosen the laundry. Take out
some of the laundry if necessary.



Close the door.



Start a programme.

Finish/Cooling down

lights

up and the drying
process is not yet
finished.

This is not a fault. The laundry is still being cooled.
The programme is just about to end.



Either remove the laundry and spread it out to cool
down or leave it in the tumble dryer to cool down
during the cooling phase.

Summary of Contents for PDR 908 EL

































































































Search results

Summary of Contents for PDR 908 EL

Reviews:

Related manuals for PDR 908 EL

Brands by name

Popular brands

Miele PDR 908 EL, Operating And Installation Instructions

Search results

Summary of Contents for PDR 908 EL

Reviews:

Related manuals for PDR 908 EL

Brands by name

Popular brands