Miele NOVOTRONIC T 7644 C Operating Instructions Manual Download Page 49

Page: 49 / 56

Extending cooldown time

You can individually lengthen the
cooldown phase the occurs before
the end of a program. Fabrics will be
more completely cooled down.

Cooldown time

– can be extended by two stages.

– it does not function for

Smoothing

programme.

For programming and saving in
memory, follow steps

The programmable function is
programmed using the buttons.

Precondition:

– The dryer is switched off.

– The door is closed.

Press

Start/Stop

and keep it pressed

it during steps

Press the

I-On/0-Off

button in.

Wait until the

Start/Stop

button lights up

continuously . . .

. . . then release the

Start/Stop

button.

Press the

Gentle

button three times.

– The

Gentle

indicator light flashes

briefly seven times.

–

and

flash alternatingly in the

display (default setting).

The number appearing alternatingly
with

means:

Default setting

Five minutes longer cooldown time

(Express

indicator light will flash

once)

Ten minutes longer cooldown time

(Express

indicator light will also flash

twice)

Pressing the

Start/Stop

button

switches from one to the other.

Using the

I-On/0-Off

button, switch

the dryer off.

The programming is now stored in
memory. You can change it again at
any time.

Programmable functions

Summary of Contents for NOVOTRONIC T 7644 C

























































Search results

Summary of Contents for NOVOTRONIC T 7644 C

Reviews:

Related manuals for NOVOTRONIC T 7644 C

Brands by name

Popular brands

Miele NOVOTRONIC T 7644 C, Operating Instructions Manual

Search results

Summary of Contents for NOVOTRONIC T 7644 C

Reviews:

Related manuals for NOVOTRONIC T 7644 C

Brands by name

Popular brands