Miele NOVOTRONIC T 7644 C Operating Instructions Manual Download Page 22

Page: 22 / 56

The lock function protects your dryer
against unauthorized use.

You can activate this function whenever
you wish.

It locks the dryer's electronics. It can be
turned on, but no program can be
started.

– In such a case, the

Gentle

indicator

light flashes and a key symbol

0-§

appears in the display.

The door may be opened at any time,
as it is not locked.

Activating the lock

Precondition:

– The dryer is switched off.

– The door is closed.

Press the

Gentle

button and keep it

pressed until Step

Press the

I-On/0-Off

button in.

The

Express

indicator light comes on.

Slowly turn the program selector

step by step through three positions
clockwise.
The three program indicator lights
must light up in succession.

Slowly turn the program selector

step by step through three positions
counterclockwise.
The three program indicator lights
must light up in succession.

The

Gentle

indicator light flashes and

the key symbol

0-§

appears in the

display.

Release the

Gentle

button.

The lock function has been activated.

You may turn off the dryer.

Deactivating the lock

Precondition:

– The dryer is switched off.

– The door is closed.

The procedure is as for "Activating
the Lock". Perform steps

At step

the indicator light for the

Gentle

button no longer flashes and the

0-§

key symbol goes out.

The lock function has been
deactivated.

Electronic lock

Summary of Contents for NOVOTRONIC T 7644 C

























































Search results

Summary of Contents for NOVOTRONIC T 7644 C

Reviews:

Related manuals for NOVOTRONIC T 7644 C

Brands by name

Popular brands

Miele NOVOTRONIC T 7644 C, Operating Instructions Manual

Search results

Summary of Contents for NOVOTRONIC T 7644 C

Reviews:

Related manuals for NOVOTRONIC T 7644 C

Brands by name

Popular brands