Miele NOVOTRONIC G 856 SC ELITE Operating Instructions Manual Download Page 40

Page: 40 / 52

What if …

Possible fault

Fix

the "End", "Start" and
"Top Solo" indicators
flash at the same time at
the end of a program?

There may be a technical
fault.

–

Turn the program selec-
tor to "Stop".

–

Turn off the dishwasher.

A few seconds later:

–

Turn the dishwasher on.

–

Select the desired pro-
gram.

–

Press the "Start" button.

If the indicators flash
again, there is a technical
problem.

–

Call the Miele Technical
Service Department.

there is a knocking
noise in the wash cabi-
net?

The spray arm is hitting
an item in the basket.

Interrupt the program, re-
arrange items blocking
the spray arms.

there is a rattling noise?

Items are not secure in
the wash cabinet.

Interrupt the program and
rearrange loose pieces.

there is a knocking
noise in the water
pipes?

This may be caused by
the installation or the di-
ameter of pipe.

This has no effect on the
dishwasher. If in doubt
contact a plumber.

the dishes are not dry,
glasses and cutlery are
spotted?

The rinse aid setting may
be too low, or the rinse aid
reservoir is empty.

Increase the dosage or
refill the reservoir, see "Be-
fore using for the first
time".

Extended drying is not ac-
tivated.

Activate the Extended
drying feature.

Dishes were taken out too
soon.

Leave dishes in longer.

Frequently asked questions

Summary of Contents for NOVOTRONIC G 856 SC ELITE





















































Search results

Summary of Contents for NOVOTRONIC G 856 SC ELITE

Reviews:

Related manuals for NOVOTRONIC G 856 SC ELITE

Brands by name

Popular brands

Miele NOVOTRONIC G 856 SC ELITE, Operating Instructions Manual

Search results

Summary of Contents for NOVOTRONIC G 856 SC ELITE

Reviews:

Related manuals for NOVOTRONIC G 856 SC ELITE

Brands by name

Popular brands