Miele KWT 6321 UG Operating And Installation Instructions Download Page 34 | Manualshive

Page: 34 / 60

background image

Active AirClean filters

34

Fresh air from the room enters the wine
conditioning unit through the Active
AirClean filter. Filtering the incoming air
through the Active AirClean filter en-
sures that all the air entering the appli-
ance is fresh and free from dust and
odours.

Replacing the Active AirClean
filter



Push the filter in and then release it.



Pull the filter out.



Detach the back part of the filter from
the cover.



Push the new filter onto the cover.



Insert the new filter.



Push the filter in and then release it.
The filter will lock into place automat-
ically with an audible click.

Active AirClean filters can be obtained
from your Miele dealer, Miele or from
the Miele website.

«
...
32
33
34
35
36
...
»

Summary of Contents for KWT 6321 UG





























































Reviews:

No comments

Related manuals for KWT 6321 UG

Milk Cafe SMF600

Brand: Sage Pages: 64

Brand: Berkel Pages: 2

ITALIA ARTISAN PIZZA OVEN

Brand: Camp Chef Pages: 15

Brand: Xavax Pages: 2

Brand: Kitchen Monkey Pages: 8

Brand: Landmark Pages: 16

Brand: Wisco Industries Pages: 7

Brand: T-Fal Pages: 36

Brand: REBER Pages: 13

Brand: Kasanova Pages: 42

Brand: SPXFLOW Pages: 22

Brand: Zelmer Pages: 31

Brand: MPM Pages: 12

Brand: Vitek Pages: 40

Brand: Vulcan-Hart Pages: 2

Sedona SUPREME SDC-S101

Brand: Tribest Pages: 68

Brand: REBER Pages: 7

Brand: REBER Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands