Miele KWT 6321 UG Operating And Installation Instructions Download Page 37 | Manualshive

Page: 37 / 60

background image

Problem solving guide

37

Display warnings

Message

Cause and remedy

A dash is lit up up/flash-
ing in the display.

Only temperatures within the range the wine condi-
tioning unit can display will be shown.

F0

or

F1

appears in the

temperature display.

There is a fault.



Call Service.

The alarm is sounding
and the temperature
display is flashing.

The temperature in the zone concerned has risen
higher or fallen lower than the temperature set.
This could be due to, for example:

– the appliance door being opened too often, or be-

ing left open,

– blocked ventilation gaps,

– a lengthy interruption to the power supply.



Rectify the cause of the alarm. The temperature
display will stop flashing and the alarm will stop.

«
...
35
36
37
38
39
...
»

Summary of Contents for KWT 6321 UG





























































Reviews:

No comments

Related manuals for KWT 6321 UG

Brand: CALOR Pages: 32

Brand: Zelmer Pages: 106

2013C(G)3.334eETsDpHbX

Brand: Hanseatic Pages: 84

Brand: Avantco Pages: 6

Brand: Nostalgia Electrics Pages: 18

Brand: Sencor Pages: 6

Brand: Sencor Pages: 13

Brand: Miele Pages: 28

Brand: Miele Pages: 48

Brand: Miele Pages: 16

Brand: Miele Pages: 16

Brand: Miele Pages: 76

Brand: Miele Pages: 92

Brand: Miele Pages: 16

Brand: Miele Pages: 4

Brand: Miele Pages: 20

Brand: Miele Pages: 8

Brand: Miele Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands