Miele G4263 Operating Instructions Manual Download Page 27

Page: 27 / 92

Before using for the first time

Setting the rinse aid dosage

You can adjust the rinse aid dosage for
best results.

The rinse aid dosage is set in stages
from 0 to 6. It is set to 3 at the factory.
This is the recommended setting.

If the "Adjust Sensor wash" programme
function (depending on model) has
been activated, the amount of rinse aid
dispensed in the

Sensor wash

programme can be higher than that set.

If spots appear on crockery and
glassware:



Increase the rinse aid dosage.

If clouding or smearing appears on
crockery and glassware:



Decrease the rinse aid dosage.



Switch the dishwasher off with the



button, if it is switched on.



Press the programme selector button



in and,

whilst holding it in

, switch

the dishwasher on using the



button.
Keep the programme selector button



pressed in for at least 4 seconds

until the lower right-hand programme
indicator light comes on.

If this does not happen, start the
procedure from the beginning again.



Press the

Turbo

button 3 times.

The

Turbo

indicator will flash rapidly 3

times at intervals.

The dosage set will appear in the
display after



The flashing sequence

 

will appear in

the display.
This indicates the factory default setting
3.



Use the programme selector button



to select the setting required.

Each press of the button moves you
up a level.

The setting is now stored in memory.



Switch the dishwasher off with the



button.

Summary of Contents for G4263





























































































Search results

Summary of Contents for G4263

Reviews:

Related manuals for G4263

Brands by name

Popular brands

Miele G4263, Operating Instructions Manual

Search results

Summary of Contents for G4263

Reviews:

Related manuals for G4263

Brands by name

Popular brands