manualshive.com logo in svg

Miele G4263, Operating Instructions Manual

Share
Download
Miele G4263 Operating Instructions Manual Download Page 20

Before using for the first time

20

Programming the water hardness
level

Switch the dishwasher off with the 

button, if it is switched on.

Press the programme selector button

 in and, 

whilst holding it in

, switch

the dishwasher on using the 

button. 
Keep the programme selector button

 pressed in for at least 4 seconds

until the lower right-hand programme
indicator light comes on.

If this does not happen, start the
procedure from the beginning again.

Press the 

Turbo

 button twice.

The 

Turbo

 indicator light will flash

rapidly twice at intervals.

The value which has been set for the
water hardness is shown as a figure
after 

 in the display (see chart).

 

 will start flashing in the display.

This is the factory default setting of
1 °d.

Use the programme selector button

 to select the value which equates

to your water hardness level.
Each press of the button moves you
up a level. When the highest water
hardness level is reached, the setting
starts from the beginning again.

The setting is now stored in memory.

Switch the dishwasher off with the 

button.

Summary of Contents for G4263





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands