Miele G4263 Operating Instructions Manual Download Page 62 | Manualshive

Page: 62 / 92

background image

Programme options

62

Optimise standby

"Optimise standby" is activated by
default.

To save energy, the dishwasher will
switch off automatically a few minutes
after the last time a button has been
pressed or after the end of a
programme.

The dishwasher will not switch off
whilst a programme is running, during
the Delay start period or if there is a
fault.

"Optimise standby" can be switched off
if you prefer. If you do this, the duration
before the dishwasher switches off
increases to 6 hours. Doing this will
increase energy consumption.



Open the door.



Switch the dishwasher off with the



button, if it is switched on.



Press the programme selector button



in and,

whilst holding it in

, switch

the dishwasher on using the



button.
Keep the programme selector button



pressed in for at least 4 seconds

until the lower right-hand programme
indicator comes on.

If this does not happen, start the
procedure from the beginning again.



Press the

Turbo

button 8 times.

The

Turbo

indicator light will flash

rapidly 8 times at intervals.

The flashing sequence in the display
shows whether "Optimise standby" is
activated or not.

–

 

: "Optimise standby" is switched

on.

–

 

: "Optimise standby" is switched

off.



Press the programme selector button



if you wish to change the setting.

The setting is now stored in memory.



Switch the dishwasher off with the



button.

«
...
60
61
62
63
64
...
»

Summary of Contents for G4263





























































































Reviews:

No comments

Related manuals for G4263

Brand: NEFF Pages: 2

Brand: NEFF Pages: 68

Brand: NEFF Pages: 2

CSOW 4963TWCE-80

Brand: Candy Pages: 32

Brand: LASA Pages: 60

Brand: ECG Pages: 188

FAVORIT 88015 VI

Brand: AEG Electrolux Pages: 36

Brand: Ariston Pages: 16

Brand: SERVIS Pages: 29

Brand: Farberware Pages: 27

Brand: Haier Pages: 16

Brand: Haier Pages: 10

Brand: Haier Pages: 10

Brand: Haier Pages: 10

Brand: Haier Pages: 19

Brand: Haier Pages: 27

Brand: Haier Pages: 9

Brand: Haier Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands