Miele G 7836 CD Operating Instructions Manual Download Page 59

Page: 59 / 64

Height:

117.5 cm

Width:

90 cm

Depth:

70 cm

Depth with door open:

126.5 cm

Voltage:

see data plate

Connected load:

see data plate

Fuse rating:

see data plate

Mains connection cable:

approx. 1.8 m

Water temperature:
Hot, cold and AD water

max. 70 °C

Static water pressure:
Hot, cold and AD water

max. 1000 kPa (10 bar) pressure

Minimum flow pressure:
Cold and hot water

150 kPa (1.5 bar) pressure

AD-water

60 kPa (0.6 bar) pressure

Recommended flow pressure:
Cold and hot water

250 kPa (2.5 bar) pressure

AD-water

150 kPa (1.5 bar) pressure

AD-water connection (non-pressurised)

Optional

Delivery head:

min. 0.6 m, max. 1 m

Drainage length:

max. 4 m

Inlet hose:

approx. 1.7 m

Drain hose:

approx. 1.5 m

Steam condenser:

approx. 2-4 l/min

Ambient temperature

from 5 °C to 40 °C

Altitude

Max. 1500 m

Noise level in dB (A):
Sound level LpA

< 70

Test marks:

VDE, interference suppression, DVGW,

mark:

MDD-Guidelines 93/42/EWG, Class IIa

If installed at altitudes above 1500 m the boiling point of the suds solution will be

lower. Disinfecting temperature parameters should be lowered and the holding
time increased (A

value).

Technical data

Summary of Contents for G 7836 CD

































































Search results

Summary of Contents for G 7836 CD

Reviews:

Related manuals for G 7836 CD

Brands by name

Popular brands

Miele G 7836 CD, Operating Instructions Manual

Search results

Summary of Contents for G 7836 CD

Reviews:

Related manuals for G 7836 CD

Brands by name

Popular brands