Miele G 7836 CD Operating Instructions Manual Download Page 39 | Manualshive

Page: 39 / 64

background image

Interrupting a programme

A programme can only be
interrupted in operating level B or D.

If you absolutely have to open the door,
e.g. because the load is obviously
unstable (conscious intervention):

After interrupting a DESIN
disinfection programme, if you wish
to continue it please check the
message in the display at the end of
the programme. If the message
PROCESS PARAMETERS NOT MET
is displayed, it means the door was
opened

after

the disinfection part of

the programme and the DESIN
parameters were not fulfilled. If
necessary the programme must be
repeated.

In operating levels B or D

^

Press the Stop button

7

. The

programme is interrupted.
If the water temperature is below
40 °C CANCEL OR

ü

CONTINUE<

will appear in the display, and if it is
above 40 °C

ü

CANCEL< will appear

in the display.

^

Open the door.

,

Warning. Water and items in the

machine may be hot. Danger of
burning or scalding.
Where a chemical disinfection
programme has been used, be
aware that steam may contain high
quantites of disinfecting agent.

^

Rearrange the load. Follow infection
control regulations and wear
protective gloves.

^

Close the door slowly.

,

If a great deal of hot water is

present in the wash cabinet when
the programme is interrupted and
the door is then closed quickly, hot
water can escape.
Danger of burning or scalding.

If the water temperature is lower than
40 °C when the programme is
interrupted:

^

Press the Start button

6

to continue

the programme.

If the water temperature is higher than
40 °C when the programme is
interrupted:

^

Press the Start button

6

.

The programme is cancelled and the
water pumped away. DRAIN WATER
appears in the display.

^

Once the water has been pumped
away, the programme can be
restarted.

Operation

39

«
...
37
38
39
40
41
...
»

Summary of Contents for G 7836 CD

































































Reviews:

No comments

Related manuals for G 7836 CD

Brand: Haier Pages: 11

Brand: Haier Pages: 11

Brand: Haier Pages: 11

Brand: Haier Pages: 17

Brand: Haier Pages: 14

Brand: Haier Pages: 2

Brand: Haier Pages: 10

Brand: Haier Pages: 35

Brand: Haier Pages: 18

Brand: Haier Pages: 28

Brand: Haier Pages: 8

Brand: Haier Pages: 40

Brand: Haier Pages: 54

Brand: Galanz Pages: 21

Brand: Gaggenau Pages: 84

Brand: saco Pages: 5

Brand: Hotpoint Pages: 56

Brand: Matsui Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands