manualshive.com logo in svg

Miele G 7782 CD, Operating Instructions Manual

Share
Download
Miele G 7782 CD Operating Instructions Manual Download Page 53

The machine must be installed and lev-
eled correctly. Any unevenness in the
floor can be compensated for by
screwing the adjustable feet in or out as
necessary. To level this unit, the service
panel and kickplate must first be re-
moved.

To remove the service panel and
kickplate:

^

Take hold of the service panel at the
top of both sides and pull forward.

^

Remove all four kickplate screws.

^

Disconnect grounding lead if neces-
sary.

^

Remove plastic protective cap.

To re-assemble:

^

Replace plastic protective cap,
kickplate facing and service panel in
the reverse order which they were re-
moved.

^

Make sure the grounding lead is
re-connected.

^

Do not use silicone sealant to seal
the gaps between the machine and
any neighboring units as this will hin-
der ventilation to the circulation
pump.

Depending on the installation require-
ments, the following kit is available:

34

1

/

4

" (87 cm) high recess

Steam deflector

For use where the machine will be
installed under a wooden countertop.
The underside of the work surface is
protected from steam damage by a
plate of stainless steel (part #1156154.)

Installation

49

Summary of Contents for G 7782 CD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands