manualshive.com logo in svg

Miele G 7782 CD, Operating Instructions Manual

Share
Download
Miele G 7782 CD Operating Instructions Manual Download Page 46

With the aid of the following explanatory
notes, minor problems can be cor-
rected without contacting the Miele
Technical Service Department.

IMPORTANT:

Any work on the washer/

disinfector electrical components
should only be carried out by a quali-
fied person.

In the event any problems cannot be
corrected, please contact the Miele
Technical Service Department.

Warning lights

DRAIN/FILL warning light flashes

^

Check that both water intake hoses
are connected to the water supply
and that the valves are turned on.

^

Check if inlet water filters are
clogged.

^

Check the drain hoses. They should
be no higher than 3 feet (1 m) from
the base level of the washer/
disinfector. The inner diameter of the
hoses should be no less then 3/4’’
(2 cm).

^

Check if any hoses are kinked. If so,
straighten.

^

Activate DRAIN cycle. Once DRAIN
is complete, restart processing cycle.

The REACTIVATION light is on

^

Replenish the water softener. Please
refer to "Reactivating the water soft-
ener".

The DETERGENT light is on

^

The liquid detergent container has to
be refilled.

The NEUTRALIZER light is on

^

The neutralizer container has to be
refilled.

The display shows two dashes

^

Contact the Miele Technical Service
Department.
The washer/disinfector must be reset
by a trained technician.

Troubleshooting

42

Summary of Contents for G 7782 CD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands