Miele G 7310 Operating Instructions Manual Download Page 106

Page: 106 / 128

Problem solving guide

106

Spray arm fault

Problem

Cause and remedy

During the programme
and at the end of the
programme, the display
shows the following
message:

Check spray arms

The dishwasher does
not switch off at the end
of the programme.
The wash items may not
be clean because no
detergent was dis-
pensed. The



Auto-

Dos

function is auto-

matically deactivated
during the programme.

The lower spray arm is blocked or the jets of the
lower spray arm are clogged. The



AutoDos

func-

tion is automatically deactivated during the pro-
gramme because the AutoDos detergent outlet can-
not be completely flushed out.



Switch the dishwasher off and back on again.

Messages appear in the display.



Perform a rotation check of the lower spray arm
and rearrange the wash items if they are blocking
the spray arm.



Clean the lower spray arm (see “Cleaning and
care” chapter, “Cleaning the spray arms” section).



Select

to confirm each message.



Start the programme again.

Summary of Contents for G 7310

































































































































Search results

Summary of Contents for G 7310

Reviews:

Related manuals for G 7310

Brands by name

Popular brands

Miele G 7310, Operating Instructions Manual

Search results

Summary of Contents for G 7310

Reviews:

Related manuals for G 7310

Brands by name

Popular brands