Miele G 7310 Operating Instructions Manual Download Page 97

Page: 97 / 128

Cleaning and care

Cleaning the drain pump

If water remains in the wash cabinet
after the end of a programme, the water
has not been pumped away. The drain
pump may be blocked by foreign ob-
jects. These are easy to remove.



Disconnect the dishwasher from the
mains.
To do this, turn off the dishwasher,
switch off at the socket and withdraw
the plug.



Take the filter combination out of the
wash cabinet (see “Cleaning and
care” chapter, “Cleaning the filters”).



Scoop the water out of the cabinet
using a suitable small container or
utensil.



Press the catch of the drain pump
cover inwards





Tip the cover inwards until it is re-
leased





Rinse the cover thoroughly under run-
ning water and remove all foreign ob-
jects.

Summary of Contents for G 7310

































































































































Search results

Summary of Contents for G 7310

Reviews:

Related manuals for G 7310

Brands by name

Popular brands

Miele G 7310, Operating Instructions Manual

Search results

Summary of Contents for G 7310

Reviews:

Related manuals for G 7310

Brands by name

Popular brands