Miele G 6570 Operating Instructions Manual Download

Page: 8 / 96

Guide to the appliance

Display

General

The display is used to select or set the

following:

– the programme
– the FlexiTimer (Delay start)
– the Settings menu

The display can show the following:

– the current time of day
– the stage the programme is at
– the estimated time left for the

programme to run

– the energy and water consumption

(EcoFeedback)

– any relevant fault messages and

information

To save energy, the dishwasher

switches off after a few minutes if you

do not press any buttons during this

time.

To switch the dishwasher back on

again, press the



button.

Settings menu

The Settings menu is used to alter the

dishwasher's electronics to suit

different requirements. You access the

Settings menu by pressing a specific

button combination (see "Settings

menu").
The arrows in the display indicate

further options. You can use the



arrow buttons next to the display, as

appropriate, to select these further

options.
The

button is used to confirm a

message or setting and also to move to

the next menu or another level.
A tick



will appear next to the option

which is currently selected.
To exit a sub-menu, use the



arrow

buttons to select the

Back 

option in

the display and confirm your selection

with

If you do not press any of the buttons

for several seconds, the display with

return to the previous level. You may

need to enter your settings again.

Summary of Contents for G 6570

































































































Search results

Summary of Contents for G 6570

Reviews:

Related manuals for G 6570

Brands by name

Popular brands

Miele G 6570, Operating Instructions Manual

Search results

Summary of Contents for G 6570

Reviews:

Related manuals for G 6570

Brands by name

Popular brands