Miele G 5266 Page 69 Operating Instructions Manual Download

Page: 69 / 92

Frequently Asked Questions

Fault messages

Problem

Possible cause and solution

The alarm tone is
sounding.
Fault number



appears in the time
display.

There may be a technical fault.



Turn the dishwasher off with the



button.



Turn the dishwasher back on after a few seconds.



Select the program you want to use.



Close the door.

If the indicator lights flash again, there is a technical
fault.



Turn the dishwasher off.



Close the faucet.



Contact Miele Service.

Fault



The drain pump may
still be running, even
with the door open.

The Waterproof system has reacted.



Turn the dishwasher off.



Close the faucet.



Contact Miele Service.

The alarm tone is
sounding.
When the door is open,
all of the program
selection indicator
lights are flashing.
Fault number

78

appears in the time
display.

Circulation pump fault.



Turn the dishwasher off.



Turn the dishwasher back on.



Select the program you want to use.



Close the door.

If the fault message appears again, there is a
technical fault.



Turn the dishwasher off.



Close the faucet.



Contact Miele Service.

Summary of Contents for G 5266





























































































Search results

Summary of Contents for G 5266

Reviews:

Related manuals for G 5266

Brands by name

Popular brands

Miele G 5266, Operating Instructions Manual

Search results

Summary of Contents for G 5266

Reviews:

Related manuals for G 5266

Brands by name

Popular brands