Miele G 5266 Page 71 Operating Instructions Manual Download

Page: 71 / 92

Frequently Asked Questions

Water intake fault

Problem

Possible cause and solution

The dishwasher stops
working shortly after
the program starts.
The alarm tone is
sounding.
The





indicator

light flashes on and off.



and

173

appear

alternately on the time
display.

The water supply faucet is turned off.



Turn on the water supply faucet fully.

The dishwasher stops
during a program.
The alarm tone is
sounding.
The





indicator

light is flashing.
The fault number





appears in the

display.

Before remedying the fault:



Turn the dishwasher off with the



button.

There is a problem with the water intake.



Turn on the water supply faucet fully and start the
program again.



Clean the filter in the water intake (see “Cleaning
the filter in the water intake” under “Cleaning and
care”).



The water connection pressure is lower than
50 kPa.
Seek professional advice.



The on-site connection for the water drainage may
be too low and you will need to vent the water
drainage (see “Water drainage” under
“Installation”).

The dishwasher stops
during a program.
Fault number

8

appears in the time
display.

A technical fault has occurred.



Turn the dishwasher off.



Close the faucet.



Contact Miele Service.

Summary of Contents for G 5266





























































































Search results

Summary of Contents for G 5266

Reviews:

Related manuals for G 5266

Brands by name

Popular brands

Miele G 5266, Operating Instructions Manual

Search results

Summary of Contents for G 5266

Reviews:

Related manuals for G 5266

Brands by name

Popular brands