Miele G 1202 Operating Instructions Manual Download Page 51 | Manualshive

Page: 51 / 68

background image

Problem

Possible cause

Remedy

Dishes, cutlery
and glasses are
not dry or are
flecked.

The amount of rinse aid
may be insufficient, or the
rinse aid reservoir empty.

Replenish the reservoir,
increase the dosage or
change the brand of rinse aid.
See "Before using for the first
time".

Crockery was taken out of
the cabinet too soon.

Leave it in for longer. See
"Operation".

Combination tabs have
been used which have
impaired drying
performance.

Set the Combi tab function to
"Normal", and fill the rinse aid
reservoir with rinse aid. See
"Additional functions".

The "Combi tab" function
has been selected, but the
wrong type of detergent
was used.

Set the Combi tab function to
the detergent product being
used (see "Additional
functions").

White residue is
visible on cutlery
and crockery,
clouding occurs
on glassware; film
can be wiped off.

Not enough rinse aid was
used.

Increase the dosage. See
"Before using for the first time
- Rinse aid".

There is no salt in the salt
reservoir.

Fill the salt reservoir. See
"Before using for the first time
- Filling the salt reservoir".

The salt reservoir cap has
not been screwed on
correctly.

Replace it, making sure that it
screws back on correctly.

An unsuitable combination
detergent has been used.

Change your detergent. Use a
standard liquid, tablet or
powder detergent.

The water softener is
programmed to a setting
which is too low.

Select a higher water softener
setting. See "Before using for
the first time".

Problem solving guide

51

«
...
49
50
51
52
53
...
»

Summary of Contents for G 1202





































































Reviews:

No comments

Related manuals for G 1202

Brand: lamber Pages: 52

Brand: Magic Chef Pages: 30

Brand: Magic Chef Pages: 8

Brand: Colged Pages: 112

Brand: Zanussi Electrolux Pages: 28

Brand: Hotpoint Pages: 16

Brand: Roper Pages: 36

Brand: Zanussi Electrolux Pages: 24

Brand: Infiniton Pages: 67

Brand: LVO Manufacturing Pages: 34

CF 1201 - 1 PHASE

Brand: VALERA Pages: 2

Lavadora y Secadora EWY8614W

Brand: EAS Electric Pages: 62

Brand: NEFF Pages: 60

Brand: GE Pages: 28

Brand: Lamona Pages: 24

Brand: Teka Pages: 65

Brand: Asco Pages: 16

Brand: GE Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands