Miele G 1202 Operating Instructions Manual Download Page 40 | Manualshive

Page: 40 / 68

background image

Adjust Sensor wash

You can adjust the Sensor wash
programme so that it will remove
stubborn soiling in a lightly soiled load.

^

Switch the dishwasher off with the
On/Off button

K

.

^

Press the Start/Stop button in and

whilst holding it in

switch the

dishwasher on using the On/Off
button

K

.

Keep the Start/Stop button pressed in
until the "Start/Stop" indicator light
comes on.

If this does not happen, start the
procedure from the beginning again.

^

Press the Delay start button five
times.

The "Delay start" indicator will flash
briefly five times at intervals.

The message flashing in the Time
display shows whether the "Adjust
Sensor wash" function is activated or
deactivated.

– "

p 1

": The "Adjust Sensor wash"

function is activated.

– "

p 0

": The "Adjust Sensor wash"

function is deactivated.

^

To change the setting, press the
Start/Stop button.

Switch the dishwasher off with the
On/Off button

K

.

Additional functions

40

«
...
38
39
40
41
42
...
»

Summary of Contents for G 1202





































































Reviews:

No comments

Related manuals for G 1202

Brand: GE Pages: 24

Brand: GE Pages: 2

Brand: Samsung Pages: 96

Brand: Panasonic Pages: 27

Brand: Samsung Pages: 44

Brand: Samsung Pages: 44

Brand: Samsung Pages: 44

WA55CG7500 Series

Brand: Samsung Pages: 76

WA70H4210S Series

Brand: Samsung Pages: 48

WD106U4SA Series

Brand: Samsung Pages: 44

Brand: Gaggenau Pages: 52

Summit DW18SSADA

Brand: Accucold Pages: 2

Brand: Logik Pages: 108

Brand: Maytag Pages: 48

Brand: Indesit Pages: 24

Brand: Belling Pages: 24

Brand: Hotpoint Pages: 20

3VT541XD - annexe 3

Brand: BALAY Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands