Miele G 1202 Operating Instructions Manual Download Page 47

Page: 47 / 68

The dishwasher does not fill/drain.

Problem

Possible cause

Remedy

The Inlet/Drain
check indicator
flashes.

The stopcock is
closed.

Open the stopcock fully.

The dishwasher
stops during a
programme.
The Inlet/Drain
check indicator
flashes.
Fault code FXX
shows in the
display.

Before rectifying the problem
you must:

– Switch the dishwasher off with

the On/Off button

Fault F12/F13:
Water inlet restricted.

– Open the stopcock fully.

– Clean the water inlet filter (see

"Maintenance").

– The water pressure at the

intake is lower than 30 kPa
(0.3 bar).
Seek professional advice.

Fault F11:
Water outlet is
restricted, water
remains in the wash
cabinet at the end of a
programme.

– Clean the filter combination.

See "Cleaning and care".

– Clean the drain pump. See

"Maintenance".

– Clean the non-return valve.

See "Maintenance".

– Remove any kink in the drain

hose.

Problem solving guide

Summary of Contents for G 1202





































































Search results

Summary of Contents for G 1202

Reviews:

Related manuals for G 1202

Brands by name

Popular brands

Miele G 1202, Operating Instructions Manual

Search results

Summary of Contents for G 1202

Reviews:

Related manuals for G 1202

Brands by name

Popular brands