Miele G 1202 Operating Instructions Manual Download Page 48

Page: 48 / 68

General problems

Problem

Possible cause

Remedy

The display is dark.

The time display switches
off automatically in
Standby Mode to save
energy.

Press any button to come
out of Standby mode.

Detergent residue is left
in the dispenser at the
end of a programme.

The dispenser was still
damp when detergent was
added.

Make sure the dispenser
is dry before adding
detergent.

The detergent
dispenser lid cannot be
closed properly.

Clogged detergent
residue is blocking the
catch.

Clean the detergent from
the catch.

At the end of a
programme there is a
film of moisture on the
inside of the door and
the interior walls.

This is caused by the
drying system and does
not indicate a fault.

The moisture will dissipate
after a short while.

Water remains in the
wash cabinet at the end
of a programme.

Before rectifying the
problem you must:

– Switch the dishwasher

off with the On/Off
button

The filter combination in
the wash cabinet is
clogged.

Clean the filter
combination. See
"Cleaning and care".

The drain pump or
non-return valve may be
blocked.

Clean the drain pump or
the non-return valve. See
"Maintenance".

The drain hose is kinked.

Remove any kink from the
drain hose.

Problem solving guide

Summary of Contents for G 1202





































































Search results

Summary of Contents for G 1202

Reviews:

Related manuals for G 1202

Brands by name

Popular brands

Miele G 1202, Operating Instructions Manual

Search results

Summary of Contents for G 1202

Reviews:

Related manuals for G 1202

Brands by name

Popular brands