Miele DA 5106 Operating And Installation Instructions Download Page 33

Page: 33 / 60

Installation

Safety distance between hob and cooker hood (S)

When planning the installation height of your cooker hood, the minimum safety

distance between the top of a cooker or hob and the bottom of the cooker

hood is as follows, unless a greater distance is specified by the manufacturer of

your cooking appliance.
See "Warning and Safety" instructions for further information.

Cooking appliance

Minimum distance S

Electric hob

450 mm

Electric grill, deep fat fryer (electric)

650 mm

Multi-burner gas hob,

total output

≤

12.6 kW, no burner

4.5 kW

650 mm

Multi-burner gas hob,

total output

12.6 kW and

≤

21.6 kW,

no burner

4.8 kW.

760 mm

Multi-burner gas hob,

total output

21.6 kW,

or multi-burner gas hob where one burner

4.8 kW.

Not possible

Single burner gas hob, output

≤

6 kW.

650 mm

Single burner gas hob, output

6 kW and

≤

8.1 kW.

760 mm

Single burner gas hob, output

8.1 kW

Not possible

Summary of Contents for DA 5106





























































Search results

Summary of Contents for DA 5106

Reviews:

Related manuals for DA 5106

Brands by name

Popular brands

Miele DA 5106, Operating And Installation Instructions

Search results

Summary of Contents for DA 5106

Reviews:

Related manuals for DA 5106

Brands by name

Popular brands