Miele DA 5106 Operating And Installation Instructions Download Page 21

Page: 21 / 60

Operation (Manual mode)

Cooking without Con@ctivity

2.0 (Manual mode)

The cooker hood can be operated

manually if:

– Con@ctivity 2.0 is not activated.
– You have temporarily deactivated

Con@ctivity 2.0 (see "Leaving

automatic mode temporarily").

Switching the fan on



Press the On/Off control



The fan will switch on at level

. The



symbol and

will light up in the power

level display.

Selecting the power level

For light to heavy cooking vapours and

odours, select from power levels

When frying or cooking food with a very

strong aroma, select the Intensive

setting



For a lower power level, press the



" control, or "



" for a higher level.

Reducing power on the intensive

setting

If Power management is activated

(default), the fan automatically switches

to level

after 5 minutes.

Selecting the run-on time

It is advisable to run the fan for a few

minutes after cooking has finished to

neutralise any lingering vapours and

odours in the air.

With the run-on option the fan switches

itself off automatically after a pre-

selected time.



After you have finished cooking,

press the run-on option control



– Once: the fan will switch itself off

after 5 minutes (

lights up).

– Twice: the fan will switch itself off

after 15 minutes (

lights up).

– If you press the run-on option control



again, the fan will remain on

(



will go out).

Switching the fan off



Use the On/Off control



to switch

the fan off.

The



symbol will go out.

Summary of Contents for DA 5106





























































Search results

Summary of Contents for DA 5106

Reviews:

Related manuals for DA 5106

Brands by name

Popular brands

Miele DA 5106, Operating And Installation Instructions

Search results

Summary of Contents for DA 5106

Reviews:

Related manuals for DA 5106

Brands by name

Popular brands