Miele ADVANTA SERIES G 2020 Operating Instructions Manual Download Page 34 | Manualshive

Page: 34 / 60

background image

Additional functions

Factory default setting

If you have altered any settings from
the factory default, you can re-set them
back to the factory default settings as
follows:

^

Switch the dishwasher off with the
On/Off button

s

.

^

Turn the programme selector to the
"12 o'clock" position.

^

Press the Start/Stop button in and

whilst holding it in

switch the

dishwasher on with the On/Off button

s

.

Keep the Start/Stop button pressed in
for at least four seconds until the
Start/Stop indicator light comes on.

If this does not happen, start the
procedure from the beginning again.

^

Turn the programme selector to the
"11 o'clock" position.

The "Wash/Rinse" indicator light will not
be lit up (indicating that at least one
setting has been altered from the
factory default settings).

^

Press the Start/Stop button.

The "Wash/Rinse" indicator will now
flash briefly at intervals (indicating that
all settings are now the factory default
ones).

^

Turn the programme selector to the
"9 o'clock" position.

^

Switch the dishwasher off with the
On/Off button

s

.

Operation

34

«
...
32
33
34
35
36
...
»

Summary of Contents for ADVANTA SERIES G 2020





























































Reviews:

No comments

Related manuals for ADVANTA SERIES G 2020

Brand: Caloric Pages: 12

Brand: Gorenje Pages: 18

Sicily Glory G01

Brand: Midea Pages: 65

Brand: AEG Electrolux Pages: 48

Brand: NEFF Pages: 29

Brand: Fisher & Paykel Pages: 5

Brand: Galanz Pages: 14

Brand: Vivax Pages: 59

Brand: Blomberg Pages: 44

Brand: Indesit Pages: 16

Brand: Hanseatic Pages: 84

Brand: Frigidaire Pages: 16

Brand: Frigidaire Pages: 9

Brand: Frigidaire Pages: 12

Brand: Frigidaire Pages: 14

Brand: Frigidaire Pages: 13

Brand: Frigidaire Pages: 11

Brand: Frigidaire Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands