Miele ADVANTA SERIES G 2020 Operating Instructions Manual Download Page 14 | Manualshive

Page: 14 / 60

background image

Programming the water hardness
level

Each time a button is pressed one of
the indicator lights will flash and light
up in the control panel. However, only
the indicator lights mentioned in the
following programming process stages
are significant.

The programming procedure can be
cancelled at any time by pressing the
On/Off button

s

. The procedure can

then be re-started from the beginning
again.

^

Switch the dishwasher off with the
On/Off button

s

.

^

Turn the programme selector to the
"12 o'clock" position.

^

Press the Start/Stop button in and

whilst holding it in

switch the

dishwasher on using the On/Off
button

s

.

Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.

If this does not happen, start the
procedure from the beginning again.

^

Turn the programme selector to the
"3 o'clock" position.

The "Wash/Rinse" programme
sequence indicator will flash briefly four
times at intervals (factory default
setting).

The number of times the "Wash/Rinse"
indicator flashes tells you which water
hardness level has been set (see
chart).

°d

mmol/l

°f

Flashing

1 - 4

0.2 - 0.7

2-

7

Once briefly

5 - 7

0.9 - 1.3

9- 13

Twice briefly

8 - 11

1.4 - 2.0

14- 20

3 times briefly

12 - 15

2.2 - 2.7

22- 27

4 times briefly

16 - 20

2.9 - 3.6

29- 36

5 times briefly

21 - 25

3.8 - 4.5

38- 45

6 times briefly

26 - 30

4.7 - 5.4

47- 54

7 times briefly

31 - 36

5.6 - 6.5

56- 65

8 times briefly

37 - 45

6.7 - 8.1

66- 80

9 times briefly

46 - 70

8.3 - 12.6

82-125

Once for longer

^

Use the Start/Stop button to select
the number of flashes which equates
to your water hardness level.
Each press of the button moves you
up a level. When the highest water
hardness level is reached, the setting
starts from the beginning again.

Example:

If your water hardness level is
4.0 mmol/l (22 °d), the Wash/Rinse
indicator should flash briefly six times
at intervals.

^

Switch the dishwasher off with the
On/Off button

s

.

Before using for the first time

14

«
...
12
13
14
15
16
...
»

Summary of Contents for ADVANTA SERIES G 2020





























































Reviews:

No comments

Related manuals for ADVANTA SERIES G 2020

Brand: Haier Pages: 13

Brand: Haier Pages: 12

Brand: Haier Pages: 15

Brand: Haier Pages: 18

Brand: Gaggenau Pages: 2

Brand: Gaggenau Pages: 68

Brand: Ariston Pages: 16

Brand: Rangemaster Pages: 28

Brand: BALAY Pages: 2

Brand: Gaggenau Pages: 52

Brand: Fisher & Paykel Pages: 12

Brand: Smeg Pages: 19

Brand: Perlick Pages: 16

WFP802B7 Series

Brand: PITSOS Pages: 8

Brand: Indesit Pages: 60

Brand: ZANKER Pages: 20

Brand: Zline Pages: 50

Brand: elvita Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands