manualshive.com logo in svg

Midtronics EXP-925, Instruction Manual

Share
Download
Midtronics EXP-925 Instruction Manual Download Page 32

EXP-925

Midtronics B.V.     Hoofdveste 6 - 8     Houten NL

www.midtronics.com

32

Chapter 12: Tester Internal Batteries

The Tester uses 6 AA, 1.5-volt batteries (alkaline 

recommended) to allow testing of batteries down to  1 volt 

and supply power while the menu is active. The analyzer can 

test batteries down to 5.5 volts when the internal batteries 

are not functioning. 

Battery Power Indicator

The square in the upper left corner of the display indicates 

the charge level of the battery pack. The square is black 

when the battery pack is fully charged. It gradually changes 

to white as the charge level declines. The Tester will display a 

warning message when the batteries need replacing.

Full

Powered 

by test 

battery

Decreasing

Low

Power Level Indicator for AA Batteries

Replacing the Tester Batteries

1.  Turn the Tester face down.
2.  Press gently on the ridges above the arrow on the bat-

tery compartment cover.

3.  Slide the cover in the direction of the arrow and remove 

the cover.

4.  Remove the discharged batteries.
5.  Insert new batteries. Make sure the positive and nega-

tive terminals are positioned correctly.

6.  Insert the door’s tabs into the slots on the analyzer and 

slide the door closed, making sure the latch locks.

Chapter 12: Tester Internal Batteries

Summary of Contents for EXP-925





































Reviews:

No comments

Brands by name

Popular brands

Load more brands