manualshive.com logo in svg

Midtronics EXP-925, Instruction Manual

Share
Download
Midtronics EXP-925 Instruction Manual Download Page 15

EXP-925

Midtronics B.V.     Hoofdveste 6 - 8     Houten NL

www.midtronics.com

15

Chapter 4: Battery Test

Out of vehicle

3.  Select the BATTERY TYPE.

1 

 REGULAR

2 

 AGM

3 

 GEL

4 

 START-STOP

Press the 

NEXT

 soft key to continue.

In case of START-STOP please see the sub-chapter ‘START-

STOP - BATTERY POST’.

4.  Select the battery’s capacity rating standard. The stan-

dard, and the rating units required are printed on the bat-

tery label. If the information is unreadable, contact the 

battery manufacturer.  

1 

 EN

2 

 EN2

3 

 DIN

4 

 IEC

5 

 SAE

6 

 JIS

7 

 CCA

Battery Standards

Rating 

System

Description

Range

EN (A)

European Norm

100 to 3000

EN2 (A) European Norm II

100 to 3000

DIN (A) Deutsche Industrie-Norm

100 to 1000

IEC (A)

International Electrotechnical 

Commission

100 to 1000

SAE (A)

European labeling of CCA

100 to 3000

JIS

Japanese Industrial Standard: 

(shown on a battery as a 

combination of numbers and 

letters.

74 numbers 

from 26A17 

to 245H52

CCA

Cold Cranking Amps (specified 

by SAE): The amount of 

current a battery can provide at 

0 ºF (–17.8 ºC).

100 to 3000

If you select JIS, the analyzer asks for the JIS part number. 

Scroll to the part number. To increase your scrolling speed, 

hold the 

UP (

)

 or 

DOWN (

) ARROW

 key, or use the 

LEFT 

(

) 

or

 RIGHT (

)

 ARROW

 key to move up or down four 

part numbers at a time. Press the 

NEXT

 soft key to continue.

5.  Press an 

UP (

)

 or 

DOWN (

) ARROW

 key to select the 

BATTERY RATING.

500

CCA

Press 

ENTER

 and begin the battery test.

6.  Select the 

TEMPERATURE

 (only asked when relevant for 

the battery decision).
Aim the tester 5 cm from the sides or top of the battery 

case. As soon as the temperature reading is stable the 

operator can press 

NEXT.

The tester will now start testing the battery. 

Start-Stop - Battery post

4.  Select the BATTERY RATING.

1 

  760A EN AGM

2 

 Q-85

3 

 T-105

4 

 OTHER

When OTHER is chosen you will have to put in the parameters 

manually.

Press the 

NEXT

 soft key to continue.

5.  Select the 

TEMPERATURE

 (only asked when relevant for 

the battery decision).
Aim the tester 5 cm from the sides or top of the battery 

case. As soon as the temperature reading is stable the 

operator can press 

NEXT.

The tester will now start testing the battery.

Summary of Contents for EXP-925





































Reviews:

No comments

Brands by name

Popular brands

Load more brands