manualshive.com logo in svg

Midtronics EXP-925, Instruction Manual

Share
Download
Midtronics EXP-925 Instruction Manual Download Page 13

EXP-925

Midtronics B.V.     Hoofdveste 6 - 8     Houten NL

www.midtronics.com

13

Chapter 4: Battery Test

Regular - Jump Start Post

5.  Select the PLATFORM.

1 

  PLATFORM 1

2 

  PLATFORM 2

3 

  PLATFORM 3

Press the 

NEXT

 soft key to continue.

6.  Select the CAR MODEL. Depending on the chosen plat-

form you will see different models, e.g.:

208 (A9)/ 2008 (A94)
C4 Cactus (E3)
OTHER

Press the 

NEXT

 soft key to continue.

7.  Select the BATTERY RATING. Again, the options you get 

here all depend on what you have chosen before.

480 A(EN)
640 A(EN)
720 A(EN)
800 A(EN)

Press 

NEXT

 to begin the battery test.

Start-stop - Battery Post

5.  Select the BATTERY RATING.

1 

  760A EN AGM

2 

 Q-85

3 

 T-105

4 

 OTHER

When OTHER is chosen you will have to put in the parameters 

manually.

Press the 

NEXT

 soft key to continue.

6.  Select the 

TEMPERATURE

 (only asked when relevant for 

the battery decision).
Aim the tester 5 cm from the sides or top of the battery 

case. As soon as the temperature reading is stable the 

operator can press 

NEXT.

The tester will now start testing the battery.

Start-stop - Jump Start Post

5.  Select the PLATFORM.

1 

  PLATFORM 1

2 

  PLATFORM 2

Press the 

NEXT

 soft key to continue.

6.  Select the CAR MODEL. Depending on the chosen plat-

form you will see different models, e.g.:

208 (A9)/ 2008 (A94)
C4 Cactus (E3)
OTHER

Press the 

NEXT

 soft key to continue.

7.  Select the START-STOP SYSTEM.

SST ALTERNATOR
SST STARTER

Press the 

NEXT

 soft key to continue.

8.  Select the BATTERY RATING. Again, the options you get 

here all depend on what you have chosen before.

760 A(EN)

Press 

NEXT

 to begin the battery test.

Summary of Contents for EXP-925





































Reviews:

No comments

Brands by name

Popular brands

Load more brands