manualshive.com logo in svg

Midtronics EXP-925, Instruction Manual, Page: 17 / 36

Share
Download
Midtronics EXP-925 Instruction Manual Download Page 17

EXP-925

Midtronics B.V.     Hoofdveste 6 - 8     Houten NL

www.midtronics.com

17

Chapter 4: Battery Test

Battery Test Results

After the test the tester will display the complete results in 
a series of screens, see below. Use the 

UP/DOWN ARROW

 

keys to scroll through each result. To send the results to the 

IR receiver, point the tester towards the IR Receiver, press 
the 

TRANSFER

 soft key and wait until the hourglass has 

disappeared from the screen.

Good Battery Result

Battery Decisions and Recommendations

Decision

Recommended Action

GOOD BATTERY

Return the battery to service.

CHARGE BATTERY

Fully charge the battery and return it to service.

CHARGE & RETEST

Fully charge the battery and retest. 

Failure to fully charge the battery before retesting 

may cause false readings. 

If 

CHARGE & RETEST

 appears again after you fully 

charge the battery, replace the battery.

REPLACE BATTERY

Replace the battery and retest. A 

REPLACE BATTERY

 result may also mean a poor 

connection between the battery cables and the battery. After disconnecting the battery 

cables, retest the battery using the out-of-vehicle test before replacing it.

BAD CELL–REPLACE

Replace the battery and retest.

FROZEN BATTERY

Thaw the battery and retest.

Battery decision

Measured voltage
Measured capacity 

rating units
Rating units you se-

lected for the test

Temperature indication

Battery’s state of charge

General health of the battery and its 

ability to deliver its specified perfor-

mance compared with a new battery

Summary of Contents for EXP-925





































Reviews:

No comments