background image

 

22

TECHNICAL NOTES

 

 

Radio Compatibility:

  Midian has taken the utmost care to ensure the option board integrates into the radio with 

minimal impact to the features of the radio.  However, some features may not be available in the radio when an 
option board is used.  If a feature is not available, please contact Midian to see if the feature can be added. 
 

Radio Firmware:

 Midian recommends installing the module into the radio with the existing firmware of the radio 

provided the firmware is at least R05.00.00. If the radio has a firmware version older than R05.00.00, it 

must 

be 

upgraded. If there are any issues with the firmware then the firmware should be upgraded to the latest. However, 
it  should  be  noted  that  occasionally  firmware  updates  may  cause  a  conflict  with  proper  option  board/radio 
communications.  This  may  appear  that  the  SVR  is  not  working  properly,  but  it  is  a  conflict  in  the  serial 
communication  between  the  option  board  and  radio.  Please  note  that  firmware  versions  between  the  EMEA 
region and the Asia and America regions might be different. 
 

Accessory  Pin  Features: 

  Upon  power-up,  the  radio  does  not  always  report  the  state  of  the  accessory  pins  to 

the  option  board.  It  may  be  necessary  to  toggle  the  state  of  these  inputs  once  after  power-up  to  ensure  correct 
operation. 
 

Option Board Feature:

  Enabling the option board feature tells the radio to report events such as button press, 

PTT press, carrier detect, etc. to the option board. This feature enables communication between the option board 
and the radio.  
 
When controlling the SVR with a radio button, it is absolutely required to enable this feature on all channels.  For 
repeat enable/disable on a per channel basis only enable the option board on repeat channels and the power up 
mode of the unit should be Power Up In Store/Retransmit Mode.  On display models, the following icon appears 
on the LCD when option board mode is on: 

 
 
 

 

MIDIAN CONTACT INFORMATION

 

 

MIDIAN ELECTRONICS, INC. 

2302 East 22

nd

 Street 

Tucson, Arizona 85713 USA 
 

Toll-Free:

 1-800-MIDIANS 

Main:

 520-884-7981 

E-mail:

 

HU

[email protected]

U

 

Web:

 

HU

www.midians.com

U

 

 

 
 

Summary of Contents for SVR-1-MPM1



























Reviews: