background image

GD  Midea  Refrigerant  Equipment  Co.  Ltd                                                                              Service  manual  for  F  Dehumidifier 

 

3.1.6 Complaint and remedy 

Complaint Cause 

Remedy 

Transformer 

(Discharge transformer 

before testing) 

Check resistance between the two input/output lines on 

transformer. Replace the transformer if either of the input/output 

is open or the transformer is damaged. 

No display on 

panel or any one of 

the button failure. 

Display board or main 

PCB failure   

Replace the display board if it is +5V else replace the main 

PCB. 

No power 

Check voltage at electrical outlet. Correct if none. 

Power supply cord 

Check voltage at the power cord terminal on Main PCB. 

Replace the power cord if none. 

Transformer 

(Discharge transformer 

before testing) 

Check resistance between the two input/output lines on 

transformer. Replace the transformer if either of the input/output 

is open or the transformer is damaged. 

Wire disconnected or 

connection loose 

Connect w ire. Refer to wiring diagram for terminal 

identification. Loose. Repair or replace loss e terminal. 

Main PCB failure 

Select fan speed and Check the voltage of P1, P2 on main 

PCB. Replace the main PCB if no voltage. 

Capacitor (Discharge 

capacitor before testing) 

Test capacitor . Replace if not within 10% of manufacture's 

rating. replace if shorted, open or damaged 

Fan motor w ill 

not run. 

Will not rotate 

Fan blade hitting shroud or blower hitting scroll. Realign 

assembly. Check fan motor bearings. Replace the motor if motor 

shaft don't rotate. 

Check voltage. Call an electrician if not with in limits. 

Test capacitor . Replace if not within 10% of manufacture's 

rating. Replace if shorted, open or damaged. 

Check bearings. Replace the motor if the fan blade can't 

rotate freely. 

Fan motor runs 

intermittently 

Revolves on over 

load. 

Pay attention to any change from high speed to low speed. 

Replace the motor if the speed does not change. 

Fan 

Replace the fan if cracked, out of balance, or partially 

missing. 

Blower 

Replace the blower if cracked, out of balance, or partially 

missing. 

Fan motor 

noise 

Loose screws 

Tighten them. 

Summary of Contents for CE-CF0.3BD/N3-F










Reviews: