background image

 

 

   

1.3 FEATURES 

Auto-defrosting. 

Suitable for low-temperature and high-humidity 

weather. 

water-full alarm and auto shutdown functions. 

Powerful dehumidification in wide temperature 

range between 5

~32

LED display. 

Humidity display and setting. 

Self diagnose and defect display 

 

 

1.4 CONTROL LOCATIONS 

       2 

 

2  

4   

 

 

        1 

 

 

 

1. ON/OFF Button: 

Power indicator links 

slowly when the power is connected at the 

socket (initial power).Press this button at this 

time, the unit will directly go into 

DEHUMIDIFYING operation with the original 

factory humidity setting( 60%RH). Press the 

button again, the unit will stop operation. 

2 . POWER indicator:

 At the first time to 

connect to the power, it flashes slowly The 

POWER indicator lights after the unit is turned 

on, and dark after the unit is turned off. 

3. FULL WATER indicator:

 Lights up when the 

bucket is full, and the unit stops operating 

 

4.CONTINUE indicator:

 Lights up when the 

unit is on CONTINUOUS DEHUMIDIFYING 

mode. 

5. HUMIDITY UP Button:

 When the unit is 

operating, the setting humidity will go up by 

pressing this button every time, the range of 

justment is from 35%RH to 80% RH. 

6. HUMIDITY DOWN Button:

 When the unit is 

operating, the setting humidity will come down 

by pressing this button every time, the range of 

adjustment is from 80%RH to 35%RH. 

7. CONTINUE Button:

 When the unit is 

operational, press the Button will go into 

CONTINUOUS DEHUMIDIFYING mode. 

8. LED Digital display:

 This area will display the 

room relative humidity under normal operation 

and display the setting humidity when setting the 

desired humidity. 

 

 

1.5 OUTSIDE DIMENSIONS

 

 

 

 

 
 
 
 

 

Model Width 

(mm) 

Height 

(mm) 

Depth 

(mm) 

CE-CF0.3BD/N3-F 

CE-CFZ0.3BD/N3-F 

315 505 235 

Summary of Contents for CE-CF0.3BD/N3-F










Reviews: