microsonic
GmbH • Hauert 16 • D-44227 Dortmund • Tel: +49 2 31 / 97 51 51-0 • Fax: +49 2 31 / 97 51 51-51 • E-Mail: [email protected] • www.microsonic.de The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features.
T1 + T2
T1
T2
T1 + T2
T1 + T2
T2
T1
Start here
T2
T1
T1 + T2
Ready
No function!
No function!
»F00«: no filter
»F01«: standard filter
»F02«: averaging filter
»F03«: foreground fil-
ter
»F04«: background
filter
Defines the strength
of the chosen filter.
»P00«: weak filter up
to
»P09«: strong filter
Minimum value: blind
zone
Maximum value: near-
window limit - 1
Low power mode
Display mode
Measurement filter
Filter strength
Foreground
suppression
Multiplex mode
device addressing
Multiplex highest
device address
No function!
No function!
Minimum value: sen-
sor-distant window
margin
Maximum value: 999
mm for mic+
25/...,mic+35/...,
999 cm for mic+
130/...,mic+340/...,
mic+600/...
Measurement range
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
T1 + T2
T1
T2
T1 + T2
T2
T1
Delay in seconds bet-
ween the detection of
an object and the out-
put of the measured
distance in case of ob-
ject approach (beha-
ves as on-delay).
"00": 0 s (no delay)
up to
"20": 20 s response
time
Response time
Choose current/
voltage output
»Aut«: automatic de-
tection of the load
»U«: voltage output
»I«: current output
T1 + T2
T1
T2
T1 + T2
T2
T1
Setting of additional functions in the LCA-2
Note
Changes in the Add-on
menu may impair the sensor
function.
A6, A7, A8 , A10 , A11, A12
have influence on the respon-
se time of the sensor.
Press on the LCA-2 simultaneously for about 13 s until «Add» is shown in the LED-display.
T1
T2
+
Detection zone
sensitivity
Affects the size of the
detection zone.
»E01«: high
»E02«: standard
»E03«: slight
T1 + T2
T1
T2
T1 + T2
T2
T1
T2
T1
T2
T1
T1 + T2
Set sensor close window
margin in mm or cm
Choose rising «
» / falling «
»
output characteristic curve
T1
T2
Set sensor-distant window
margin in mm or cm
Press on the LCA-2 simultaneously for about 3 s until welcome message has passed
T2
T1
T1 + T2
T2
T1
Set analogue output
Ready
Start here
Optional setting of parameters using the LinkControl Adapter LCA-2 (Offline programming)
T1 + T2
T1 + T2
T1 + T2
T1
T2
+
Offline programming
■
Load Sensor parame-
ters in the LinkControl
Adapter LCA-2
■
Change parameters
and additional functi-
ons as described here
■
Write changed para-
meters back into the
lcs- sensor
Please refer to the quick refe-
rence guide on the LCA-2.
