3
to devices that meet the system requirements for
the Kinect Sensor, including running Windows, and
to protect the technical limitations and security
systems in the Kinect Sensor.
2. Warranty
The Software is covered by the Limited Warranty for Your Kinect
Sensor, and Microsoft gives no other guarantee, warranty,
or condition for the Software. No one else may give any
guarantee, warranty, or condition on Microsoft’s behalf.
3. EXCLUSION OF CERTAIN DAMAGES
MICROSOFT IS NOT RESPONSIBLE FOR ANY INDIRECT,
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES; ANY
LOSS OF DATA, PRIVACY, CONFIDENTIALITY, OR PROFITS; OR
ANY INABILITY TO USE THE SOFTWARE. THESE EXCLUSIONS
APPLY EVEN IF MICROSOFT HAS BEEN ADVISED OF THE
POSSIBILITY OF THESE DAMAGES, AND EVEN IF ANY REMEDY
FAILS OF ITS ESSENTIAL PURPOSE. Some countries do not
allow the exclusion or limitation of incidental or consequential
damages, so this limitation or exclusion may not apply to You.
4. Choice of Law
The laws of the country in which you purchased the Kinect
Sensor govern the interpretation of this agreement, any claim
that Microsoft breached it, and all other claims (including
consumer protection, unfair competition, implied warranty,
and tort claims), regardless of conflict of law principles. This
agreement applies to the maximum extent permitted by law
and unless prohibited by law. This agreement does not change
Your rights under the laws of Your State or country if the laws of
Your State or country do not permit it to do so.
REGULATORY INFORMATION
• Any changes or modifications not expressly approved by
Microsoft could void the user’s authority to operate this
device.
• This product is for use with NRTL Listed (UL, CSA, ETL, etc.),
and/or IEC/EN 60950-1 compliant (CE marked) Information
Technology equipment.
• No serviceable parts included.
• This device is rated as a commercial product for operation at
+41ºF (+5ºC) to +95ºF (+35ºC).
This Class B digital apparatus complies with, as applicable, Part
15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Model: 1656 (Kinect for Windows v2 sensor).
Microsoft Corporation; One Microsoft Way; Redmond, WA
98052-6399; U.S.A. United States: (800) 426-9400.
Radio and TV interference regulations
The Microsoft hardware device(s) can radiate radio frequency
(RF) energy. If not installed and used in strict accordance with
the instructions given in the printed documentation and/or
onscreen Help files, the device may cause harmful interference
with other radio-communications devices (for example AM/
FM radios, televisions, baby monitors, cordless phones, etc.).
However, there is no guarantee that RF interference will not
occur in a particular installation.
To determine whether your hardware device is causing
interference to other radio-communications devices, disconnect
the device from your computer. If the interference stops, it was
probably caused by the device. If the interference continues
after you disconnect the hardware device, turn the computer
off and then on again. If the interference stopped when the
computer was off, check whether one of the input/output (I/O)
devices or one of the computer’s internal accessory boards is
causing the problem. Disconnect the I/O devices one at a time
and see whether the interference stops.
If this hardware device does cause interference, try the
following measures to correct it:
• Relocate the antenna of the other radio-communications
device (for example AM/FM radios, televisions, baby
monitors, cordless phones, etc.) until the interference stops.
• Move the hardware device farther away from the radio or TV,
or move it to one side or the other of the radio or TV.
• Plug the computer into a different power outlet so that the
hardware device and radio or TV are on different circuits
controlled by different circuit breakers or fuses.
If necessary, ask your computer dealer or an experienced
radio-TV technician for more suggestions. For more information
about interference issues, go to the FCC website at:
fcc.gov/cgb/consumerfacts/interference.html. You can also
call the FCC at 1-888-CALL FCC to request Interference and
Telephone Interference fact sheets.
Laser specifications
CAUTION
Use of controls or adjustments, or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
This device complies with International Standard IEC 60825-
1:2007 for a Class 1 laser product. This device also complies with
21 CFR 1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
The following Class 1 laser label is located on the bottom of
the sensor:
Disposal of electrical and electronic equipment
This symbol on the product or its packaging means
that this product must not be disposed of with your
household waste. Instead, it is your responsibility to
hand this over to an applicable collection point for
the recycling of electrical and electronic equipment.
This separate collection and recycling will help to conserve
natural resources and prevent potential negative consequences
for human health and the environment due to the possible
presence of hazardous substances in electrical and electronic
equipment, which could be caused by inappropriate disposal.
For more information about where you should dropoff your
electrical and electronic waste, please contact your local city/
municipality office, your household waste disposal service, or
the shop where you purchased this product. Contact weee@
microsoft.com for more information about waste from electrical
and electronic equipment.
This product is for use with NRTL-listed (UL, CSA, ETL, etc.)
and/or IEC/EN 60950 compliant (CE marked) Information
Technology equipment.
COPYRIGHT
Information and views expressed in this document, including
URL and other Internet website references, may change without
Class 1 laser produCt
IeC 60825-1:2007-3
Summary of Contents for KINECT FOR WINDOWS V2
Page 32: ...32...
