manualshive.com logo in svg

MicroNet SP5004P, User Manual

Share
Download
MicroNet SP5004P User Manual Download Page 16

 

                                                                                                                                               

 

 

 

 

 

15

 

 

This page is the PPPoE configuration page. Most of the ISPs request the user to connect 
to central office (CO) side via PPPoE, acronym of Point-to-Point Protocol over Ethernet, 
which provides authentication, authorization and accounting. 

User Name 

Enter the user name provided by your ISP to identify the computer 
using PPPoE. 

Password 

Enter the password provided by your ISP to identify the computer using 
PPPoE. 

Please retype your password

 

Retype the password to make sure type correct password. 

Service Name 

Some ISP provides the service name of this PPPoE connection. If so, 
enter this item, or make it blank. 

MTU (546-1492) 

Maximum Transmission Unit (MTU) is the largest physical packet size 
measured in bytes, which a network can transmit. Any messages 
larger than the MTU are divided into smaller packets before sent. In 
ordinary, that the user does not have to worry about the MTU size, the 
gateway routing engine will handle the MTU differences between PPP 
and the LAN Ethernet side. But for some old PPPoE server, you have to make the MTU 
size of the PPPoE side smaller than the default value, or some Web side is not able to 
access. 

Summary of Contents for SP5004P































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands