Micron MTFDJAK200MBW Manual Download

Page: 21 / 37

Table 18: SAS Command Set and Additional Supported Bits – SED and Non-SED (Continued)

Command

Op-Code

(Hex)

Sub-Command/

Functional Bit

Description

Supported

Read (12)

–

READ (16)

–

Yes

READ (32)

7F/0009

–

Yes

READ BUFFER
(Mode 0, 2, 3, A, and B)

1Ch

Error history

Yes

READ CAPACITY (10)

–

Yes

READ CAPACITY (16)

9E/10

–

Yes

READ DEFECT DATA (10)

–

Yes

READ DEFECT DATA (12)

–

Yes

REASSIGN BLOCKS

–

Yes

RECEIVE DIAGNOSTIC RESULTS

–

Yes

00h

Supported diagnostic pages

Yes

40h

Translate page

RELEASE (6)

–

Yes

RELEASE (10)

–

Yes

REPORT IDENTIFYING
INFORMATION

05h

–

Yes

REPORT LUNS

–

Yes

REPORT SUPPORTED OPERA-
TIONS CODES

0Ch

–

Yes

REPORT SUPPORTED TASK
MANAGEMENT FUNCTIONS

0Dh

–

Yes

REQUEST SENSE

–

Yes

–

Actual retry count bytes

Yes

–

Extended sense

Yes

–

Field pointer bytes

Yes

RESERVE (6)

–

Yes

–

3rd party reserve

Yes

–

Extent reservation

RESERVE (10)

–

Yes

–

3rd party reserve

Yes

–

Extent reservation

REZERO UNIT

–

Yes

SANITIZE

–

Yes

01h

Overwrite

Yes

02h

Block erase

Yes

1Fh

Exit failure mode

Yes

SEEK (6)

–

Yes

S600DC Series 2.5-Inch SAS NAND Flash SSD

Commands

CCMTD-1725822587-3891
s600dc_series_2_5_sas_ssd.pdf - Rev. H 9/17 EN

Micron Technology, Inc. reserves the right to change products or specifications without notice.

Summary of Contents for MTFDJAK200MBW






































Search results

Summary of Contents for MTFDJAK200MBW

Reviews:

Related manuals for MTFDJAK200MBW

Brands by name

Popular brands

Micron MTFDJAK200MBW, Manual

Search results

Summary of Contents for MTFDJAK200MBW

Reviews:

Related manuals for MTFDJAK200MBW

Brands by name

Popular brands