24
The ignition of the lamp is seven times unsuccessful (the HEAt message appeared six
times before), and the display shows
"LAEr
", meaning that the lamp could be damaged or
even missed, the fixture is overheating (this can occur if the ambient temperature is 40° C or
more) or there could be a failure on the ignitor or ballast.
Please place or replace the lamp, check the ambient temperature or contact your dealer if
the situation was not caused by the lamp.
This message informs you that the main PCB does not communicate correctly with the
Control Board.
(Color-wheel 1 error) This message will appear after the reset of the fixture if the mag-
netic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is
defective (or its driver circuit on the main PCB). The color-wheel is not located in the default
position after the reset.
(Color-wheel 2 error) This message will appear after the reset of the fixture if the mag-
netic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is
defective (or its driver circuit on the main PCB). The color-wheel is not located in the default
position after the reset.
(Rotating gobo-wheel error) This message will appear after the reset of the fixture if
the magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-
motor is defective (or its driver circuit on the main PCB). The rotating gobo-wheel is not lo-
cated in the default position after the reset.
(Rotating gobo indexing error) This message will appear after the reset of the fixture
and if the magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driver circuit on the main PCB). The rotating gobo is not
located in the default position after the reset.
(Static gobo-wheel error) This message will appear after the reset of the fixture if the
m agnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-
motor is defective (or its driver circuit on the main PCB). The gobo-wheel is not located in
the default position after the reset.
(Prism-wheel error) This message will appear after the reset of the fixture if the mag-
netic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepping-motor is
defective (or its driver circuit on the main PCB). The prism -wheel is not located in the default
position after the reset.
This error message informs you that the fixture was overheating (occurred if the ambi-
ent temperature is 40° C or more) and that the relay switched off the lamp. This message will
appear on the display until the temperature will be on a suitable level, then the display will
show the HEAt message meaning the lamp is too hot (explanation see above).
This message appears if the lamp lighting sensor is failed. Please contact your dealer.
This message will appear if the fixture was shortly disconnect from the power supply.
(PAN-yoke movement error) This message will appear after the reset of the fixture if
the yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB). The yoke is not located in the
default position after the reset.
(TILT-head movement error) This message will appear after the reset of the fixture if
the head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB). The head is not located in
the default position after the reset.
This message will appear if the frequency of the mains is not standard 50 or 60 Hz.
5
ENGLISH
1.2 Description of the Fixture
1
- Projector-head
2
- Yoke
3
- Left side panel
4
- Base
5
- Control Board
6
- Right side panel
7
- Carrying handles
Left side panel:
8
- Power-switch
9
- Power cord
10
- Fuse holder
Right side panel:
11
- DM X-output
12
- DMX-input
Control Board:
13
- Mode-button
14
- Display
15
- Enter-button
16
- Up/Down-buttons
