MHSC SB44SS Installation, Operation And Maintenance Manual Download Page 32

SB44SS Outdoor Woodburning Fireplace

3

87D0059

FIrepLaCe MaINTeNaNCe

At the end of each heating season or when the fireplace will not be in use for an extended time, 
the ashes should be removed and the hearth area should be swept as clean as is practical.  The 
slow absorption of moisture into the ashes over a long period of time could cause a condition which 
would be corrosive to the metal fireplace parts.
At the beginning of each heating season, always operate the flue damper and make sure it has not 
become stuck from soot, creosote, etc., during the period of inactivity.
Keep the lower and upper grille panels clean and free from dirt and lint accumulation at all times to 
get the maximum efficiency from your fireplace.
As you use the fireplace, expansion and contraction will cause minor cracking of the hearth, back, 
and side refractory materials.  This is normal and unavoidable.  If the cracks become large enough or 
parts dislodge and metal behind the refractory is exposed, the refractory panels should be replaced 
with new panels that can be obtained from you fireplace dealer.

gLaSS dOOr MaINTeNaNCe

For glass door maintenance, see instructions provided with the glass doors.

CheCkLIST OF dO’S aNd dONT’S

DO’S

1.  Do check with local building officials to be sure the installation of the fireplace complies with all 

building codes and requirements and obtain required building permits. Do plan your installation 
with safety as you primary consideration.

.  Do use only the prescribed material and parts for the installation of the fireplace.
3.  Do insulate the exterior walls surrounding the fireplace to prevent excessive heat loss from the 

fireplace.

4.  Do trim the face of the fireplace only with noncombustible materials.
5.  Do attach the noncombustible face trim material firmly to the face of the fireplace.
6.  Do  block  in  or  fasten  the  fireplace  to  prevent  the  possibility  of  the  fireplace  shifting  out  of 

position.

7.  Do enclose the chimney where it passes through living spaces or spaces accessible for storage 

purposes to prevent contact with and possible damage to the chimney.

8.  Do install firestop spacers at each ceiling level when the chimney is installed in a multistory 

building.

9.  Do install the proper chimney cap or chimney housing on the chimney to prevent rain and debris 

from entering the chimney.

10.  Do keep all flammable liquids, gases and pressurized containers away form the fireplace.
11.  Do check the fireplace for proper adjustment and operation before leaving it unattended for long 

periods of time.

1.  Do inspect and clean the fireplace chimney regularly.
13.  Do keep the fire screens closed when the fireplace is left unattended to minimize the danger of 

sparks popping out of the fireplace.

14.  Do use the grate furnished with and for this fireplace.
15.  Do start a fire only with paper, kindling or solid composition fire starters specifically designed 

for starting a fire.  The use of liquid fire starter can cause an explosion within the fireplace.

16.  Do place all ashes in a metal container with a tight fitting lid and place them on a 

noncombustible 

surface  well  away  from  other  combustible  materials  until  they  have  completely 
cooled.

MaINTeNaNCe and SaFeTy 

Summary of Contents for SB44SS





































Reviews: