MHSC SB44SS Installation, Operation And Maintenance Manual Download Page 3

SB44SS Outdoor Woodburning Fireplace

87D0059

3

SaFeTy INFOrMaTION

pLeaSe read ThIS MaNuaL BeFOre INSTaLLINg aNd uSINg FIrepLaCe.
IMpOrTaNT: 

Read all instructions and warnings carefully before starting installation. Failure to fol-

low these instructions may result in a possible fire hazard and will void the warranty.

preCauTIONS

MHSC fireplaces and component parts have been highly 
tested and will operate safely when installed in accordance 
with instructions provided in this manual. Carefully read and 
understand all instructions 

before

 beginning installation.

If you notice any damage to fireplace or component parts, 
immediately report damage to your MHSC dealer.
Only use MHSC components or the warranty will be voided 
and a fire hazard may be created.
MHSC warranty will be voided by and MHSC  disclaims any 
responsibility for the following actions:

• 

Installation by any other than a qualified installer, 
preferably NFI or WeTT (Canada) certified.

• 

Installation of any damaged fireplace or chimney 
component;

• 

Modification  of  fireplace,  chimney  assembly  or 
any component parts thereof; (except for chase 
flashings as detailed in the Chimney Cap instal-
lation instructions).

• 

Installation  other  than  as  instructed  by  MhSC; 
or

• 

Installation  and/or  use  of  any  component  part 
not  manufactured  or  approved  by  MhSC  in 
combination or assembly with a MhSC fireplace 
system, notwithstanding any independent testing 
laboratory or other third party approval of such 
component parts or accessory.

any such action may possibly cause a fire hazard.

Consult local building codes to ensure that you are in com-
pliance 

before 

installing the fireplace.

Fireplaces must be vented to the out-of-doors.

WarNINg: To avoid the risk of damaging fireplace 
materials and increasing the risk of spreading a fire, 
do not use the fireplace to cook or warm food.
do not obstruct or modify air inlets/outlets in any man-
ner. 
do not install combustible materials on any of the black 
fireplace surround.
Burn only solid wood fuel or gas logs.
do not install a solid fuel burning insert or other prod-
ucts not specified for use with this fireplace.
WarNINg

: Do not pack required air spaces with combustible 

material or insulation not specifically recommended for use 
in such areas.

proposition 65 Warning:

 Fuels used in gas, wood-

burning or oil fired appliances, and the products of 
combustion of such fuels, contain chemicals known to 
the State of California to cause cancer, birth defects 
and other reproductive harm.
California Health & Safety Code Sec. 549.6

WarNINg: Check with your electronics manufacturer 
before installing a television or other electronic device 
above this fireplace.
This fireplace is not designed to be water tight. 
Therefore, when installing this unit against an exte-
rior wall, the wall must be finished before setting unit 
in place.

MOISTure reSISTaNCe

This outdoor fireplace will shed moderate amounts of 
water, but is not waterproof. Water and condensing water 
vapor may enter the chase under certain conditions.
The fireplace will not perform as an exterior wall. Mois-
ture penetration must be considered for construction 
that places the fireplace in structure walls or on moisture 
sensitive surfaces.
When installed on exterior walls: MHSC recommends 
the fireplace chase be constructed outside the structure's 
weather envelope. Where the platform meets the wall, 
use a flashing detail similar to that required for attached 
decks. Chase platforms, including hearths should slope 
away from the structure at 1/4 in per foot. The fireplace 
can be shimmed level.
When installed on surfaces where water may collect or 
cause damage: MHSC recommends a slope of 1/8 in 
to 1/4 in per foot towards the drain port suggested. The 
fireplace can be shimmed level.
Hearths should slope away from the front of the fireplace 
and chase at 1/8 in to 1/4 in per foot. Metal safety strips 
must be on top of any combustible hearth materials used 
for moisture management.

draFTS

The  fireplace  should  not  be  located  in  areas  that  create 
drafts (ie: frequently opened doors and central heating air 
inlets/outlets) that hamper the normal flow of air into the 
fire.

gaS LOgS

If you plan to install a gas log, the gas line should be installed 
before framing the fireplace. The gas line must be installed 
by a certified gas line installer.  

Summary of Contents for SB44SS





































Reviews: