manualshive.com logo in svg

MHS Boilers Ultramax WM 100, Operating & Maintenance Manual, Page: 37 / 50

Share
Download
MHS Boilers Ultramax WM 100 Operating & Maintenance Manual Download Page 37

MHS Boilers Ltd © 

 

191007 

37

Setting the required flow temperature for central heating system operation. 
 
Attention! This setting is not active if a KKM6/8, E6/8 or BME/BM8, or an external 0-5 V signal is 
connected. 

- Open the lid of the KM 628, and a black arrow will appear above P1. 
- Press the reset/programming button (item 3); the red LED will light up, then turn the rotary 
selection switch until the desired temperature appears in the display. 
- Again press the reset/programming button: the red LED will go out 
- The new flow temperature will now be active 
- Close the lid. 

 
Set the required hot water temperature for hot water operation. 
This is only applicable if the hot water mode is being used. 

- Open the lid 
- Turn the rotary switch until the arrow at the bottom of the LED displays parameter P2 
- Press the reset/programming button (item 3), the LED lights up, then turn the rotary switch 
(item 5) until the desired hot water temperature appears in the display 
- Again press the reset/programming button; the LED will go out 
- The new value will now be active 
- Close the lid 

 
6.4 Fault signals 

In the case of the fault, a flashing 

 

and an error code will constantly appear in the display. In the 

case of a fault, the cause should first be eliminated before the relevant safeguard is reset. The OK 
signal will be lost if a fault occurs more than twice within 6 minutes (the error code will be shown 
in the display with a “3” appearing above it), or in the case of a fault that remains active for more 
than 6 minutes. 
 

1 High Limit thermostat (STB) has been triggered 

If the flow temperature has risen above 100

°

C the high limit will be activated. 

Wait until the flow temperature is below the value set for at least one minute and then reset this 
safety function by pressing the reset button.

 

 

2/3 Interlock circuit has been interrupted 

An external safety device connected to the terminals (ST 9.3-9.4) has been triggered. Check and 
repair this safety device. 
 

4 No flame signal when the burner starts 

No flame is detected within the preset safety time when burner starts. Restart is possible if 
programmed. 
 

5 Flame signal lost during operation 

When the burner is in operation, the measured ionisation has fallen below 1

µ

A. 

 
 

Summary of Contents for Ultramax WM 100



















































Reviews:

No comments