manualshive.com logo in svg

MHS Boilers Ultramax WM 100, Operating & Maintenance Manual, Page: 25 / 50

Share
Download
MHS Boilers Ultramax WM 100 Operating & Maintenance Manual Download Page 25

MHS Boilers Ltd © 

 

191007 

25

Ultramax BMS Run and Fault Indication Relays (Optional Extra) 

 

 

Terminal Designation (Boiler Run Indication Relay) 

Controller 

Terminal 

#s 

Relay 

Terminal 

#s 

Voltage 

Description/Operation/Function 

ST11.4 

A1 

230V 

Relay Coil Live Input From Terminal ST11.4   

Located on the rear of the KM628 boiler controller. 

ST11.3 

A2 

230V 

Relay Coil Neutral Input From Terminal ST11.3  

 Located on the rear of the KM628 boiler controller 

N/A 

COM 

External Control System 

Dependant (230V 0.5 Amp Max) 

Input Connection For Boiler Run Indication. 

(Common Terminal of Single Pole Double Throw Relay Switch) 

N/A 

NO 

External Control System 

Dependant (230V 0.5 Amp Max) 

Output Connection For Boiler Run Indication. 

(Normally Open Terminal of Single Pole Double Throw Relay Switch) 

N/A 

NC 

External Control System 

Dependant (230V 0.5 Amp Max) 

Terminal Not usually Used For Boiler Run Indication Relays  

(Normally Closed Terminal of Single Pole Double Throw Relay Switch) 

Terminal Designation (Boiler Fault Indication Relay) 

Controller 

Terminal 

#s 

Relay 

Terminal 

#s 

Voltage 

Description/Operation/Function 

ST1.2 

A1 

230V 

Relay Coil Live Input From Terminal ST1.2 Located on the rear of 

KM628 boiler controller. (Terminal ST1.1 Located on the rear of KM628 

boiler controller must connected to terminal 1 on main terminal rail to 

provide a 230v supply) 

Boiler 

Terminal 2 

A2 

230V 

Relay Coil Neutral Input From Terminal 2 

N/A 

COM 

External Control System 

Dependant (230V 0.5 Amp Max) 

Input Connection For Boiler Fault Indication. 

(Common Terminal of Single Pole Double Throw Relay Switch) 

N/A 

NO 

External Control System 

Dependant (230V 0.5 Amp Max) 

Terminal Not usually Used For Boiler Fault Indication Relays 

 (Normally Open Terminal of Single Pole Double Throw Relay Switch) 

N/A 

NC 

External Control System 

Dependant (230V 0.5 Amp Max) 

Output Connection For Boiler Fault Indication. (Normally Closed 

Terminal of Single Pole Double Throw Relay Switch) 

Summary of Contents for Ultramax WM 100



















































Reviews:

No comments