MHS Boilers Ultramax WM 100 Operating & Maintenance Manual Download Page 17 | Manualshive

Page: 17 / 50

MHS Boilers Ultramax WM 100 Operating & Maintenance Manual Download Page 17

MHS Boilers Ltd ©

191007

17

- Calibration of the room sensor
- Delay to flow temperature compensation due to external temperature up to a maximum of
3 hours
- Holiday Programme
- Frost protection system based on external temperature or room temperature
- Remote activation via telephone if no external room sensor fitted (external relay required)
- Optimisation of compensation slope based on room temperature and external temperature
with optimum start time adjustment
- Hot water Anti-legionella bacteria function
- Option of switching off internal room sensor
- 2-wired communication (scom-bus)
- Display in 6 different languages
- External display of KM628 functions with display of status, operating hours, number of starts,
degree of modulation and temperatures.

BM8 Room Unit
Room Unit Mounting Plate Wiring Terminals

Terminal Designation
When connected to a Single Ultramax Boiler (2 Wire SCOM)

Terminal #s

Voltage

Screened Cable (Earthed

Screening)

Description/Operation/Function

3 & 5

(Polarity Sensitive)

<25V

Yes

SCOM Communication to boiler

(3 - & 5 +)

3 & 6

(Not Polarity Sensitive)

<25V

Yes

Tamperproof RFB Remote

Sensor or Volt Free Enable

1 & 2 & 4

-

-

Not Used

When connected to a KKM8 or E8 Manager/Controller via a COCO2 (4 Wire CAN)

Terminal #s

Voltage

Screened Cable (Earthed

Screening)

Description/Operation/Function

1 & 2 & 3 & 4

(Polarity Sensitive)

<25V

Yes

CAN Communication to Controller

1 H, 2 L, 3 –, 4 +

3 & 6

(Not Polarity Sensitive)

<25V

Yes

Tamperproof RFB Remote Sensor

or Volt Free Enable

5

-

-

Not Used

«
...
15
16
17
18
19
...
»

Summary of Contents for Ultramax WM 100



















































Reviews:

No comments