background image

61  

  [email protected]

!

LOCK

Model: 

Netti Dynamic AdaptPro

Language: 

English

 

Version:

 

2021-11

My-Netti.com

6.8.7 LEG SUPPORT FOOT BOARD

Netti Dynamic DUAL leg supports are equipped with 

a foot board. It is linked to the left leg support and 

folds down into a foot board lock in the right leg 

support.

FOOT BOARD LOCK

With both leg supports in place, let the foot board 

swing down and put the bolt into the lock, see 

pictures to the right. 

Rotate the outer ring to lock it.

 

  Always lock the foot board when the user sits 

in the chair. It is essential for the function of 

the dynamic system that the foot board is 

locked. Failing to lock may lead to damage to 

the leg supports  and eventual also harm to 

the user.

6.8.8 LOCKING DYNAMIC LEG SUPPORTS  

The Netti Dynamic Dual Leg support angle can be 

locked by tightening the red wheel on the outside of 

the leg supports. See illustration:

This stops dynamic movements except rotation of the 

foot board.

  

Always lock the dynamic function of the leg 

supports when the user sits in the chair and  

it is used as a seat in a car

.

Summary of Contents for Netti AdaptPro













































































Reviews: