Metso Outotec Lokotrack ST4.10 Driving Instruction Download

Page: 5 / 40

DRIVING INSTRUCTIONS

D100014616-EN

398 0 EN 2021-06-22

1. DRIVING INSTRUCTIONS

These driving instructions are valid for Lokotrack ST4.8 and Lokotrack ST4.10. The purpose of these

instructions is to enable safe moving of the machine during transportation.

NOTICE:

Do not use the machine for screening solely based on these instructions. The

actual instruction manual for the machine is delivered separately.

NOTICE:

In these driving instructions, it is assumed that the machine is in the transport

position. If needed, see the actual instruction manual of the machine for

information on how to prepare the machine for transportation.

The illustrations in this instruction may not fully correspond to your machine.

1.1. SAFETY

Because of the size and weight of the machine, pay special attention when moving the machine. It is highly

recommended that a banksman is used when the machine is moved.

DANGER!

GENERAL HAZARD
Will cause death or serious injury.
Read the safety section before working with the machine. Only competent and

trained personnel are allowed to work with the machine.

WARNING!

PERSONAL INJURY HAZARD
Can cause death or serious injury.
Before starting and during track driving the machine, make sure that there

are no persons in the area whose safety may be endangered. Walk around

the machine and make sure that there is nobody on, by or below the machine.

Warn everybody in the vicinity before starting.

WARNING!

CRUSHING HAZARD
Can cause death or serious injury.
Do not drive the machine in locations where there is a risk of squeezing.

Always drive the machine from a safe distance. If possible, drive the machine

from either end of the machine.

Summary of Contents for Lokotrack ST4.10









































Search results

Summary of Contents for Lokotrack ST4.10

Reviews:

Related manuals for Lokotrack ST4.10

Brands by name

Popular brands

Metso Outotec Lokotrack ST4.10, Driving Instruction

Search results

Summary of Contents for Lokotrack ST4.10

Reviews:

Related manuals for Lokotrack ST4.10

Brands by name

Popular brands