Metso Outotec Lokotrack ST4.10 Driving Instruction Download Page 38

Page: 38 / 40

DRIVING INSTRUCTIONS

D100014616-EN

398 0 EN 2021-06-22

DRIVING INSTRUCTIONS

Figure 45: Location of hydraulic shut-off valve

1.12.17. RECOVERING FROM TOO HIGH HYDRAULIC OIL TEMPERATURE

If the hydraulic oil temperature is too high, a message “A6: Process running prevented: Too high hydraulic

oil temperature“ or “A3: Engine running prevented: Too high hydraulic oil temperature“ is displayed in the

message field on the top left corner of the main control panel display.

Check the hydraulic oil temperature by doing the following:

1. From the main view of the control panel display, tap Information views (3).
2. Tap ST information (1).

Callout

Description

ST information view

Hydraulic oil temperature

Information views

Figure 46: ST information view

The hydraulic oil temperature is shown in the hydraulic oil temperature field (2).

3. Wait for the hydraulic oil to cool down until the temperature is below +60°C (140°F).
4. Try starting the engine again.

Summary of Contents for Lokotrack ST4.10









































Search results

Summary of Contents for Lokotrack ST4.10

Reviews:

Related manuals for Lokotrack ST4.10

Brands by name

Popular brands

Metso Outotec Lokotrack ST4.10, Driving Instruction

Search results

Summary of Contents for Lokotrack ST4.10

Reviews:

Related manuals for Lokotrack ST4.10

Brands by name

Popular brands