ENGLISH
en
7
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work (see
chapter 10.), thus less particles enter the
environment in an uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
-
For efficient dust collection, use a suitable
Metabo M-class vacuum cleaner together
with this power tool.
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits
- Use an extraction unit and/or air purifiers
- Maintain good ventilation of the workplace and
keep clean using a vacuum cleaner Sweeping or
blowing will stir up dust
- Vacuum or wash your protective clothing Do not
blow, beat or brush.
Symbols on the tool:
.......... Class II Construction
V ............. volts
A ............. amperes
Hz ........... hertz
W ............ watts
Ø............. max. diameter of the accessory
.../min...... revolutions per minute
rpm ......... revolutions per minute
~ ............. alternating current
n ............. rated speed
See page 2.
1 Bar auxiliary handle *
2 Thumb screws of the bar auxiliary handle *
3 Locking discs of the bar auxiliary handle *
4 Threaded holes on gear housing
5 2-hole spanner
6 Adjusting nut
7 Diamond cup wheel*
8 Support flange
9 Spindle
10 Spring-mounted ring brush
11 Spindle locking button
12 Extractor connection piece
13 Opening segment (for working close to walls)
14 Safety guard
15 Handle
16 Trigger (for switching on and off)
17 Electronic signal indicator
18 Speed adjustment wheel
* depending on equipment/not in scope of delivery
Before plugging in the machine, check that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Australia: Always use a residual current device
(RCD / GFCI) protected supply with a rated
residual current of 30 mA or less.
5.1 Fitting of bar auxiliary handle
Always work with the bar auxiliary handle (1)
attached! Fit the bar auxiliary handle as shown
(see illustration A, page 2).
- Fit locking discs (3) to the left and right of the gear
housing.
- Fit the bar auxiliary handle (1) at the gear housing.
- Insert the thumb screws (2) left and right into the
bar auxiliary handle (1) and turn gently.
- Adjust the bar auxiliary handle (1) to the required
angle.
- Firmly tighten the thumb screws (2) to the left and
right manually.
5.2 Dust extraction
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (12).
For optimal dust extraction, use the connecting
sleeve 6.30796.
We recommend using an antistatic suction hose
with diameter 35 mm.
Disconnect the mains plug before changing
any accessories. The machine must be
switched off and the spindle must be at a standstill.
6.1 Locking the spindle
Press in the spindle locking knob (11) only
when the spindle is stationary!
- Press in the spindle locking button (11) and turn
the
spindle (9) by hand until you feel the spindle
6.2 Fitting/removing the diamond cup wheel
See illustration B on page 2.
To fit:
- Fit the support flange (8) on the spindle. (9) The
flange should not turn on the spindle when prop-
erly attached.
- Lay the diamond cup wheel (7) on the support
flange (8) so that it lies flat along the support
- The two sides of the clamping nut (6) are different.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (6) is facing upward.
- Lock the spindle (see chapter 6.1). Turn the
clamping nut (6) clockwise using the 2-hole
To remove:
- Lock the spindle (see chapter 6.1). Turn the
clamping nut (6) anticlockwise using the 2-hole
4. Overview
5. Initial Operation
6. Attaching the accessory
