background image

As at 09/07

14

 Chapter 4: Binary inputs

4.2

 

Binary inputs, 4-gang

 Binary input REG-K/4x24

Multi-function.counter 12BA/1.0

Art. no. 644892

You can use the counter reset function to reset the im-
pulse counter and the cycle time or the switching 
counter of another input. Additionally, you can use this 
function to transmit switching commands.

You can determine whether the count should be reset 
while the pulse edge is rising or falling, or while it is 
both rising and falling.

Additionally, you can program a switching telegram to 
be transmitted when the pulse edge is rising and/or fal-
ling. 

Communication objects

You can select the following communication objects:

You can use the cyclical monitoring function to trans-
mit telegrams cyclically. This is necessary when other 
devices are monitoring the presence of the push-but-
ton interface via their cyclical telegrams (protection 
against theft, fault monitoring). If no telegram is recei-
ved from the push-button interface within a paramete-
risable time period, e. g. a signal is issued by this 
device. For this purpose, you can parameterise the 
push-button interface accordingly.

|

When a disable function is activated via the 
disable object, all current push-button functions 
are reset or interrupted.

Communication objects

You can select the following communication objects:

You can block the inputs in two different ways:

1. Separately for each input

2. All inputs function as a master input

You can determine whether a disable object = 0 or = 1 
should be blocked.

Separately for each input

You can use this function to block each of the four or 
eight inputs individually. When an input is blocked, it 
fulfils no function. You can use an additional parameter 
to parameterise the behaviour of cyclical functions.

All keys function as a master input

You can use this action to specify one of the two or 
four inputs as the master input. When any key is 
pressed, the action which has been parameterised for 
the master key is carried out.

Resetting the counter

Tab

Parameter

Input X

Functional selection

Influences input (1-4)

Behaviour on rising pulse edge

Behaviour on falling pulse edge

Counter and cyclic interval

Function

Object name

Type

Prio

Flags Behaviour

Reset coun-
ter

Switch object A 1 bit

Low

WCT Transmit

Cyclical transmission for devices with cyclical 
monitoring

Tab

Parameter

Input X

Functional selection

Operating mode

Number of objects

Tab

Parameter

Input X (object A/B)

Object A/B

Action when activated

Action on release

Value 1

Value 2

Base for cyclic interval

Factor for cyclic interval (3-255)

Function

Object name

Type

Prio

Flags Behaviour

Cyclical mo-
nitoring

Object A/B

1 bit/
2 bit/
4 bit/
1 byte

Low

WCT Transmit

Activating the disable function for the inputs

Tab

Parameter

Input disable function

Disable function

Blocking

Behaviour at start of 
blocking

Master input

Tab

Parameter

Inputs X: Block

Input x

Cyclical actions are

Tab

Parameter

Input X

Functional selection

Type of blocking

Master input

Summary of Contents for REG-K/4x24






















Reviews: