background image

11

INSTALLATION

SETTING THE LIIMITS FOR RIGHT OR LEFT HAD OPERATION AND FORCE

14

the opener will operate during this procedure. Make sure the door is clear of obstruction. Ensure your hands 

are away from any moving parts before activating the door.

Travel limits set how far your door goes up and down. Your opener must also be configured for right or left hand installation. If not 

the door will rotate in the reverse direction. 

Program Buttons:

 The Control Panel diagram in section 4 identifies the Control Buttons and LED layout 

Audible Beep: 

An audible “BEEP” also occurs with each button press. This feature can be turned OFF 

Courtesy light:

 During the programming sequence, the courtesy light will flash at half strength 

NOTE: The WeatherDrive (MR555MYQ) opener is factory configured for right hand installation.

Setting the Right or Left Hand Operation:

Refer to the diagrams on the right for guidance. 

Ensure the door is positioned halfway and the opener is engaged 

(out of manual mode). 

Turn the opener Power 

ON

, the courtesy light will turn ON.

1.  Press the “P” button for 5 seconds until LED 3 will flash, as well 

as LED 2 or LED 1 will flash. For Right Hand setting LED 2 will 

flash, and for Left Hand setting LED 1 will flash.

2.  To change to the opposite setting, simply press the “S” button, 

and the opposite LED will flash.

3.  When the correct hand setting is selected, Press and Release 

the “P” program button to accept this setting. (continue).

Setting the Door Limits:

4.  Press and hold the “UP” button until the door 

reaches the desired OPEN position (You can toggle between 

the “UP” and “DN” buttons to move the door to the correct 

position. Ensure the bottom rail stops 50 mm below the 

mechanical stops mounted to the door guides).

5.  Press and release the “P” program button to 

accept this setting.

6.  Press and hold the “DN” button until the door reaches the 

desired CLOSED position (You can toggle between the UP and 

DN buttons to move the door to the correct position).

7.  Press and release the “P” program button to accept this setting. 

(LED 2 should flash to indicate you are now in Force Learn 

mode).

Setting the Force Automatically:

8.  Press and release the “UP” button. The door will travel to the 

OPEN position with LED 2 flashing.

9.  Press and release the “DN” button. The door will travel to the 

CLOSED position with LED 1 flashing. When fully closed, LED 1 

will stop flashing and the courtesy light will change to full power.

This process is now complete

Setting the Force manually: (Only perform if Limits are already 

set)

•  Start with the door fully CLOSED.
•  Press the “S” button twice to enter into force learn mode. The 

courtesy light will go to half strength, and LED 2 will flash 

quickly.

•  Press and release the “UP” button. The door will travel to the 

OPEN position, then LED 1 will flash quickly.

•  Press and release the “DN” button. The door will travel to the 

CLOSED position, then LED 1 will stop and the courtesy light 

will change to full power.

This process is now complete.

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

DN

DN UP

UP P

P

S

S

1

1

2

2

3

3

132A2940

1. Program

Start

2. Left/Right

Setting

3. Accept

Setting

4. Set UP

Limit

5. Accept UP

Limit

6. Set DOWN

Limit

7. Accept

DOWN
Limit

8. Learn UP

Force

9. Learn

DOWN
Force

Flash
x 2

Flash
x 2

Flash
x 2

Flash
x 2

Flash
x 2

Flash
x 2

Full
light

BEEP

BEEP

BEEP

BEEP

BEEP

BEEP

BEEP

DOWN

DOWN

UP

UP

Summary of Contents for Merlin WeatherDrive MR555MYQ

























Reviews: